Airsoft Sniper Parts (UK)

Spring is King!

Not sure what model of rifle you have?

Browse the images below to help try and find what rifle you have and if there's any hope for it!




ASG VFC Ashbury ASW338LM

This rifle is useless in stock form and must be upgraded to be useful. However, when upgraded these perform very well. You just need to man up to the weight of it.

ASG released an upgrade cylinder, cylinder internals and their own 90 degree zero trigger. These can be hard to find however if you wish to stick with the cheaper 45 degree upgrade route we have some upgrades available.

See:  http://www.airsoftsniperparts.com/apps/webstore/products/category/762709?page=1


  

 

TM L96 AWS

The TM Version has the Mag in the correct location. Be careful not to break the loading ramp or loading plate when upgrading.

PDI offer a complete 90 degree upgrade set which is expensive. If you wish to stick with the 45 degree upgrade route i.e. swap out the parts like for like please see our webstore.

http://www.airsoftsniperparts.com/apps/webstore/products/category/874977?page=1

TM VSR Pro & G-Spec

The original and still pretty much the best platform to work with but also one of the most accurate rifles in stock form or upgraded. A genuine TM will have stamped markings on the left side of the outer barrel.

We have plenty of parts available for this rifle. You can opt for 45 degree or 90 degree (recommended) upgrade route. Please see our upgrade guide under the "More" Tab.

For a range of upgrades please see: http://www.airsoftsniperparts.com/apps/webstore/products/category/639219?page=1

JG Bar10 Pro & G-Spec    (aka ASG Covert OPS, JG366 & JG367)

A good quality Chinese clone of the TM version. Accepts the same upgrades as the TM version.  A great alternative for a base rifle if you're on a budget, especially if you are going upgrade all the internals! These usually have "J G Works" stamped on the side to help identify them from other clones. They also often come shipped with illuminated reticule scopes.

Parts available: http://www.airsoftsniperparts.com/apps/webstore/products/category/639219?page=1

Warrior, Well, Maruzen & Mauser L96 MB-01

The original version was made by Maruzen. Since then Chinese re-brands such as Well, Mauser and Warrior have cloned the Maruzen and thus the parts fit. Our upgrade parts are designed for the common Chinese clones. The parts are based on the APS2 Type96 flavour.

We have an upgrade guide on our website under the "More" Tab.

Parts are available from our webstore.  Please see: http://www.airsoftsniperparts.com/apps/webstore/products/category/639220?page=1

WELL MB-03

Based on VSR internals yet again. However the barrel is longer, it's approx 495mm so a standard VSR barrel will be too short. Also, notice how this VSR clone has a RIS rail at the front underneath the stock. The mag release catch is also rounded rather than flat like the TM or JG.

The stock cylinders are weak aluminium so it's recommended that you replace this at the first opportunity. The stock cylinders don't like 45 degree pistons when used with a high tensile spring. The bolt pull is quite hard. We recommend using a 90 degree trigger setup such as our EZ Trigger.

Part are available from our webstore, http://www.airsoftsniperparts.com/apps/webstore/products/category/880766?page=1

WELL MB-04 & MB-05

These rifles are the MB-01's in fancy stocks. Parts are available via our webstore, see: http://www.airsoftsniperparts.com/apps/webstore/products/category/639220?page=1

Well MB-06 SR2 aka ASG Urban Sniper

These are very light and come with a left / right hand conversion kit so great if you're a leftie. They use similar parts to the MB-01 except the trigger and cylinder is different.

We have parts available to fully upgrade these rifles, see: http://www.airsoftsniperparts.com/apps/webstore/products/category/764410?page=1

Well MB-07

Based on the VSR system, these rifles utilise the 45 degree setup. However, the cylinders are very weak and it's advisable to replace the cylinder when upgrading. The stock cylinders are of very poor quality and such the bolt becomes very stiff when upgraded with a high tensile spring at 500 fps using a 45 degree piston. We highly recommend going the 90 degree route when upgrading these rifles.

Also note, we have seen some odd QC issues so be prepared to do a little tinkering here and there to get them working just right.

Upgrade parts are available from our webstore, see: http://www.airsoftsniperparts.com/apps/webstore/products/category/639219?page=1


WELL MB-08

These rifles are the MB-01's in fancy stocks. Parts are available via our webstore, see: http://www.airsoftsniperparts.com/apps/webstore/products/category/639220?page=1

NOTE: MB-01 Silencer adapters do not fit this model.

Well MB-10

Based on the VSR system, these rifles utilise the 45 degree setup. However, the cylinders are very weak and it's advisable to replace the cylinder when upgrading. The stock cylinders are of very poor quality and such the bolt becomes very stiff when upgraded with a high tensile spring at 500 fps using a 45 degree piston. We highly recommend going the 90 degree route when upgrading these rifles.

Also note, we have seen some odd QC issues so be prepared to do a little tinkering here and there to get them working just right.

Upgrade parts are available from our webstore, see: http://www.airsoftsniperparts.com/apps/webstore/products/category/639219?page=1

A&K Dragunov - also compatible with King Arms (AtoZ)

A spring clone of more expensive manufacturers. They utilise a quick spring change mechanism to change FPS in a matter of minutes. This rifle uses AEG springs. These have distinctive Blue aluminium pistons. The hops are a good design but reports suggest the range is lacking. We have introduced a new improved hop unit along with other upgrades available from our webstore, see: http://www.airsoftsniperparts.com/apps/webstore/products/category/639221?page=1


Snow Wolf / Classic Army M24

The CA version uses a unique trigger. However it does use APS2 Type96 Spring guides, pistons and springs.

We can get hold of steel cylinders for these rifles, please contact us direct if required.

We don't offer a wide range of parts for this rifle and recommend visiting PDI's distributer, X-Fire.


Snow Wolf M24

There are two versions. One VSR based and the other APS based. We supply parts or the APS version.

Versions based on APS internals take APS2 Type96 Cylinder internals i.e. piston, spring and spring guide. Other parts such as trigger and cylinders are unique but we do have a selection of replacement and upgrade parts available, please see our webstore: http://www.airsoftsniperparts.com/apps/webstore/products/category/690514?page=1

These rifles are know to have very bad hop units, however we now supply a professional replacement. Please see above link.

HFC VSR-11

Another china clone of the TM VSR. This version is one of the better ones. All VSR parts are compatible with this rifle. See our webstore for options: http://www.airsoftsniperparts.com/apps/webstore/products/category/639219?page=1

Swiss Arms SA1

A very nice looking rifle, which looks like the VSR. However this rifle has no  known readily available full upgrade kits available. As such, avoid at all costs for serious skirmishers. Backyard plinking only.

If you're not sure, one tell tale sign this is an SA1 is by the placement of the front sling hook. It's not under the stock but literally at the front under the outer barrel.

Maruzen APS2 EX

Old skool rifles, you don't see these in the shops any longer. However these are some of the most accurate rifles out there.

Some versions have fixed hops which you can use different size o-rings to set the hop. Others, you can obtain aftermarket hop unit replacements.

The triggers are different from that of the MB-01 but the piston sear is the same. Cylinder internals such as spring, spring guide and piston are compatible with the MB-01 and as such we have some parts available for this rifle, see: http://www.airsoftsniperparts.com/apps/webstore/products/category/640268?page=1

Snow Wolf Barrett M99

These use the same cylinder internals as the MB-01. However the cylinders and triggers are different. Some upgrade parts are available via our webstore: http://www.airsoftsniperparts.com/apps/webstore/products/category/690514?page=1

 

ARES Walther WA2000

The ARES version is based on TM VSR internals. Parts are available here: http://www.airsoftsniperparts.com/apps/webstore/products/category/946453?page=1

ASG AW .308

Made in the same factory as the DE version, the ASG AW.308 is a hybrid rifle despite it looking like the common Well MB-01.

This rifle uses APS2 Type96 Cylinders*, spring guides, cylinder heads, springs and hop buckings. However the trigger and piston use 45 degree surfaces.

If you wish to udnertake a simple upgrade you can use L96 spring guides and VSR M170 springs. However if you wish to upgrade them properly you will have to convert them to the MB-01 format.

You'll need to replace the whole trigger, piston, spring guide, spring and cylinder.**

Parts are available from our webstore here: http://www.airsoftsniperparts.com/apps/webstore/products/category/885483?page=1

* Cylinder locking section at rear of bolt handle is different from standard MB-01 thus, MB-01 cylinders will fit (there's no alternative) however the rear back pice doesn't lock into place which can allow the bolt handle to over rotate however careful cocking technique will prevent this.

** Some filing may be required around entry of receiver to allow upgrade cylinder to slide in smoothly.

This rifle is a hybrid, it can be tricky to upgrade, if possible avoid and opt for the Well MB-01 version.

There are no known hop upgrades available. However the hop unit can be replaced with our Air Seal hop chamber if used with an AEG barrel.

ARES MSR MS-338 and MS-700

The difference between the 338 and 700 versions is the mag well is slightly bigger on the 338 however internally they are the same.

In stock form the have a unique trigger. The sears are not compatible with any other rifle. However the cylinder, cylinder head, piston, spring, spring guide and hop bucking are all VSR compatible. The barrels are 420mm in length but it is possible to use a standard VSR 430mm barrel as it ends just before the flash hider.

These rifles have got a bad reputation for slam firing early on. However we supply MMC Pro 90 degree triggers which can be installed to remove this problem completely.

The hop unit is unique but does use the TDC (top dead centre) method of adjustment.

After upgrading, these rifles are impressive and equal in performance to the TM VSR.

See our Facebook photos for a complete break down of the internals.

Parts are available here: http://www.airsoftsniperparts.com/apps/webstore/products/category/971866?page=1

ARES MCM700X

Compatible with VSR Cylinders, Cylinder Heads, Pistons, Spring Guides, springs and hop buckings.

We also have specialised 90 degree triggers from MMC in store.

See:

Snow Wolf VSR-10

Cheap TM VSR clone, however internally, it's a hybrid.

This rifle uses the same trigger as the SW M24, an APS Trigger. It uses VSR springs and Spring Guides. The psiton however is the same that is used in the common MB-01.

It's identifiable as the cylinder has been crimped at the end to secure the bolt handle yet it does not have a RIS rail like the Well MB-03.

Parts are available here: http://www.airsoftsniperparts.com/apps/webstore/products/category/933522?page=1

ASG Steyr SSG 69 P2

Very much a starter rifle. No dedicated upgrades are available for this rifle. Most owners tend to undertake DIY modifications to get this rifle performing. AVOID!

Well MB-11

Very much underestimated rifles. These, like the MB-07 are VSR based. You can use VSR internals to upgrade this rifle however due to poor china QC we'd recommend opting for the 90 degree upgrade route.

Parts are available from here: http://www.airsoftsniperparts.com/apps/webstore/products/category/639219?page=1

King Arms Blaser R93

Unique in the best part. Please visit TNT Pro Sniper Shop for upgrades.

ASG Concern Izhmash Dragunov SVD

aka ARES Dragunov SVD - yes ARES had them branded in the first release!

These share the same piston as the A&K version however the hop units are not.

The trigger sear is also compatible with the A&K version but you'll need to drill a small hole underneath for a spring to slot in.

Swiss Arms SAR-10 (Bull Barrel)

Another cheaper clone of the TM VSR. This one is based on the G-Spec model.

It is VSR compatible! Parts available here: http://www.airsoftsniperparts.com/apps/webstore/products/category/639219?page=1

DE L96 M57A

Pretty much the same rifle as the ASG AW.308 - please read information on ASG AW.308 above.

Often, these come in orange two tone colour.

DE M50

No known available upgrade sets available. The cylinders are often seal to and not accessible. Avoid!

Well AWP(S) MA4402D

A clone of the TM L96 AWS.

ASG Zastava M70 varmint

Not much information on this. From what we've seen they use VSR Trigger and Piston Sears but the cylinder width is smaller than VSR thus it uses a VSR style piston which is has a smaller width similar to the MB-01. It also uses MB-01 cylinder heads. There are no known upgrade kits for this rifle. Avoid.

Well MB-09

Real Wood version of the MB-10. Details found earlier, above on this web page.

UHC Super9

A starter rifle, surprisingly reliable. Usually sits around the 400 fps velocity. No known readily available upgrade kits are available for this rifle. Often seen in Green two tone. Avoid.

Note: Tokyo Soldier released a Gas version which has a good reputation.

AGM L96

One of the worst L96 clones ever released. These are no longer retailed new. They are a hybrids.

They use VSR triggers but the cylinders are thinner than VSR, they are the same width as the APS cylinders. They take VSR springs and spring guides BUT the piston, albeit VSR shaped, is not VSR sized, the width is smaller to fit in the cylinder. The hop is VSR style but is pretty much inaffective. There are no known readily available upgrades for this rifle although in the past some US Retailers did manufacture upgrade kits you'll be lucky to obtain one nowadays. AVOID!!!

Note: Easily identifiable as the have VSR G-Spec style bolt handles!

Beta Project Intervention

Pretty much unique although not much information is out there. Some US retailers have parts available, see: http://www.evike.com/product_info.php?products_id=42596

It takes AEG hop buckings and nubs.

ARES / ASG AW338

They are compatible with VSR 45 degree pistons, spring guides, springs, cylinder heads and hop buckings. Upgrades availavble here: http://www.airsoftsniperparts.com/apps/webstore/products/category/1048978?page=1

DBOYS Kar98

Shell ejecting. They come with either plastic or weal wood stocks. Pretty much unique. They don't use conventional barrels or buckings. Often people uses washers over the spring guide to increase the fps. You can use a clipped APS spring but this can lead to hard bolt pull/push.

Zeta Labs Mosin Nagant

No information available. This rifle is very much unique.  Disassembly guide here: http://www.youtube.com/watch?v=loRRvtWyRwo